Electric Field, Radio Frequency (RF) Field, Magnetic Field Strength Meter by Tri

Description

AutoDS Template
Store
New Arrivals
Add to Favorite
View Feedback
Contact
Electric Field, Radio Frequency (RF) Field, Magnetic Field Strength Meter by Trifield – EMF Meter Model TF2 – Detect 3 Types of Electromagnetic Radiation with 1 Device – Made in USA by AlphaLab, Inc.
Electric Field, Radio Frequency (RF) Field, Magnetic Field Strength Meter by Trifield – EMF Meter Model TF2 – Detect 3 Types of Electromagnetic Radiation with 1 Device – Made in USA by AlphaLab, Inc.
Product Description
NEW! From AlphaLab, Inc. makers of the original TriField Meter Model 100XE.
The TriField EMF Meter Model TF2 is an AC gaussmeter, AC electric field meter, and radio power density meter in a single unit, that combines all the features needed for fast, accurate measurements of electromagnetic fields (EMF). In addition to standard AC measurement modes, a special frequency weighted mode will properly scale the magnetic and electric measurements to indicate the full magnitude of currents produced by each type of field inside the human body. (If only powerline frequency is present, Standard and Weighted will read the same. If higher frequencies are present, Weighted reads higher). Made in USA by AlphaLab, Inc.
Magnetic (“MAG”) Fields-- Turn the knob to Standard MAG or Weighted MAG. Read the large numerals in the center. In a typical home or office with low EMF, living areas will read 3.0 milligauss or less on Standard MAG and 5.0 milligauss or less on weighted. In a car (gas or electric), the reading may be higher. “Weighted” emphasizes the frequencies that are higher than powerline frequencies, while “Standard” measures all frequencies equally. Some home locations, such as near the breaker box, will have a higher magnetic field. If you rarely or never visit these high-field areas, the high reading is not important. The fields are only important in locations where you spend time.
The magnetic readings show the field at the location where the meter is held, and is independent of how you orient the meter. It is also independent of whether your hand is blocking the meter. However, the electric (“ELEC”) and RF detectors are different. These sensors read the field correctly when the top of the meter is pointed toward the source, but your hand CAN block these fields, so hold the meter by its lower half when measuring electric or RF.
Electric (“ELEC”) fields-- In an electromagnetically quiet home or office, both Standard and Weighted will read less than 50 V/m, but the reading may be higher when the meter is pointed toward fluorescent lights, a wall outlet or switch plate, or an improperly-grounded appliance.
RF-- This meter reads RF and microwaves in the frequency range 20 MHz to 6 GHz. This includes most new 5G installations, but not experimental millimeter wave 5G. Only the total power level from all sources is displayed. No information regarding specific frequencies is displayed.
Digital RF signals are pulsing. This means that the peak power density (see PEAK on the upper left of the screen) is higher than the average power density (main number in center) and you will see the bars pulse up and down if digital RF signals are present. THE MAIN (AVERAGE) NUMBER MAY BE FLUCTUATING. THIS IS A PROPERTY OF DIGITAL SIGNALS; IN THIS CASE, THE PEAK NUMBER IS MORE CONSISTENT. A “smart meter” from your electric power company only pulses about once a minute. To read this pulse strength, hold the TF2 near the “smart meter” and wait for the bars to jump. Then read the PEAK number, which will hold for several seconds. Smart Meters from the gas company pulse much less frequently (perhaps only once a day) so it is difficult to read RF from them, but they pulse so infrequently that it is probably irrelevant. Wi-Fi routers, that are broadcasting, pulse more than once a second. Computers (and other devices that are on line with a WiFi router) emit much less RF power than a router. Microwave ovens leak a significant amount of RF, but it is more continuous, not digital pulses. An RF quiet area will typically have less than 1.000 milliwatts per square meter as a peak (highest PEAK reading after watching the meter for a minute), and 0.200 average (the large numerals). RF can be effectively shielded by placing any metal sheet (aluminum foil or aluminum siding) or metal mesh (aluminum screen door material) between you and the RF source, which is typically a cell tower. Metal sheet or mesh affects RF in the same way that a mirror reflects light. Note that both RF and electric field are affected by where you stand or position your hands relative to the meter. These fields are usually stronger near the surface of your body because you are electrically conductive. If you hold the meter, it will read the field correctly in the vicinity of your hand. If you set the meter down, the reading will often be lower because the field is lower away from your hand. Inside an elevator, the RF and electric field are essentially zero. Unlike several other meters which have a false high reading in RF, the TF2 actually reads near zero in this environment. Near zero-field environment can also be achieved by wrapping the meter in aluminum foil (except for a small opening to see the display). This demonstrates how well foil will shield RF and electric field.
New Features and Improved Specifications
Easy to use: just turn the knob to the type of field to be measured
Detects all three types of EMF pollution: AC magnetic, AC electric, and RF/microwave
Large LCD for crystal clear, accurate readings with adjustable backlight
Peak Hold captures fast pulses, for measuring fast digital signals
Sensitive RF mode for measuring the signal from mobile phones and Wi-Fi EMF. Specific frequency information is NOT displayed.
AC magnetic measurements are 3-axis, allowing for quick readings, regardless of meter orientation
Unique feature-- does both standard AC readings and weighted (emphasizes high frequencies)
Specifications
AC Magnetic
Sensor Type
3-axis, true magnitude
Frequency Range (NOT displayed)
40 Hz – 100 kHz
Accuracy
±4% @ 50/60 Hz
Maximum Range
100.0 milligauss
Sensitivity (Resolution)
0.1 milligauss
AC Electric
Sensor Type
1-axis, true magnitude
Frequency Range (NOT displayed)
40 Hz – 100 kHz
Accuracy
±5% @ 50/60 Hz
Maximum Range
1000 V/m
Sensitivity (Resolution)
1 V/m
RF/Microwave
Sensor Type
1-axis
Frequency Range (NOT displayed)
20 MHz – 6 GHz
Accuracy
±20% @ 1 GHz
Maximum Range
19.999 mW/m^2
Sensitivity (Resolution)
0.001 mW/m^2
Battery Details
Battery (included)
9V alkaline battery with indicator
Battery Life Backlight Off
> 20 hrs
Battery Life Backlight On
> 12 hrs
Detects all three types of EMF pollution: AC magnetic, AC electric, and RF/microwave
Displays signal level, peak level, and a fast indicator bar (for pulse monitoring)
AC magnetic, AC electric, RF/Microwave (measures total RF signal but NOT frequency)
AC fields: can measure standard measurements or weighted (proportional to current induced in the human body)
Made in USA; 1-Year Manufacturer Warranty
Product Dimensions: Length: 2.75in Width: 5.25in Height: 1.5in
Package Dimensions: Weight: 0.7875 pounds
Find More of our winning products
Men's Fashion
Women's Fashion
Hotest Selling Items
About Us
Welcome to our eCommerce shop. We're dedicated to providing you with high-quality products at unbeatable prices. Our professional customer support team is more than happy to help with anything that you need.
We’re proud to serve you and bring a smile to your face with our top-notch service and products. Please visit our eBay store for a full list of products on sale, and don’t miss what we have to offer.
Payment policy
We only accept payments made by PayPal.
Please make sure that your PayPal and eBay shipping addresses match.
Immediate payment is required before we send out your package.
Shipping policy
We are always working hard to ensure your package arrives as soon as possible. Please understand that some factors like weather, high postal traffic, and the performance of shipping companies are outside of our control.
In most cases, your package will arrive before due time as it is a high priority for us. If there are any unexpected delays, please let us know and we will take care of it immediately.
We have multiple locations in the US; residents of these states will be charged tax according to the state they reside in. Tax information is available at checkout.
Returns
We are committed to your happiness. That’s why we offer a 30-Day Return Policy on items that you are not completely satisfied with. You have the option for a refund or an exchange of the item. No returns are available on items shipped outside of the USA.